Geomechanics and Engineering
Instructions to Authors
(Last updated: Oct 25, 2021)
Introduction
This Instruction to Authors is to provide help for authors who wish to submit their papers in double column format to some Techno-Press journals. For the list of Techno-Press journals in double column format: (Journals)
1. Submission of the paper
Authors are asked to submit manuscripts in PDF (or Latex) format electronically through the Techno-Press Manuscript Upload System (TeMUS) (http://www.techno-press.com/papers). Exceptionally, the special issue papers may be directly submitted to the Guest Editor. If you have difficulties in using TeMUS, please contact us at[gae@techno-press.com]. On receiving submitted papers, the system will issue the paper ID and Password to the corresponding author, which may be conveniently used to check the status of submitted papers.
2. Preparation of the manuscript
General : The manuscripts should be in English and typed with double column and single line spacing on single side of A4 paper. Submitted papers will be published in the category of regular technical papers only. The first page of an article should contain: (1) a title of paper which well reflects the contents of the paper (Arial, 15pt), (2) all the name(s) and affiliations(s) of authors(s) (Arial, 11pt), (3) an abstract of 100~250 words (Times New Roman, 9.5pt), (4) 5-10 keywords following the abstract, and (5) footnote (personal title and email address of the corresponding author (required) and other authors' (not mandatory)). The paper should be concluded by proper conclusions which reflect the findings in the paper. The normal length of the technical paper should be about 8-16 journal pages (double column format).
Please refer to Authors’ Guide(A):http://www.techno-press.com/papers/Guide(A).pdf
Template(A): http://www.techno-press.com/papers/Template(A).docx
Tables and figures : Tables and figures should be consecutively numbered and have short titles. They should be referred to in the text as following examples (e.g., Fig. 1(a), Figs. 1 and 2, Figs. 1(a)-(d) / Table 1, Tables 1-2), etc. Tables should have borders (1/2pt plane line) with the captions right before the table. Figures should be properly located in the text as an editable image file (.jpg) with captions on the lower cell. All of the original figures and tables are required to be placed at the suitable location in the text. It should be avoided whenever possible that a figure or table occupies both columns, in particular, it should not be stretched from one end to another.
Units and mathematical expressions : It is desirable that units of measurements and abbreviations should follow The International System of Units (SI) except where the other unit system is more suitable. The numbers identifying the displayed mathematical expression should be placed in the parentheses and referred to in the text as following examples (e.g., Eq. (1), Eqs. (1)-(2)). Mathematical expressions must be inserted as an object (set as Microsoft Equations 3.0) for Microsoft Word 2007 and later versions. Image-copied text or equations are not acceptable unless they are editable. The raised and lowered fonts cannot be used for superscription and subscription.
References : A list of references which reflect the current state of technology in the field locates after conclusions of the paper. For details to prepare the list of references and cite them in the text, authors are advised to follow the introduction and the sample list in the Authors' Guide of the instruction.
3. Review
All the submitted papers that have passed the preliminary check by the editors will undergo a rigorous peer-review process to judge their significance and originality. Those papers positively recommended by at least two expert reviewers will be finally accepted for publication in the Techno-Press Journals.
4. Proofs
Proofs will be sent to the corresponding author to correct any typesetting errors. Alterations to the original manuscript will not be accepted at this stage. Proofs should be returned within 48 hours of receipt.
5. Copyright
Submission of an article to a Techno-Press Journal implies that it presents the original and unpublished work, and not under consideration for publication elsewhere. On acceptance of the submitted manuscript, it is implied that the copyright thereof is transferred to the publisher. The Agreement of Authorship, Originality, and Copyright Transfer must be signed and submitted.
6. Ethics
General: Techno-Press applies research and publication ethics standards based on COPE's International Standards for Editors and Authors (https://publicationethics.org/node/11184). Violation of publication ethics will result in the activation of COPE flow chart. (https://publicationethics.org/guidance/Flowcharts)
Authorship: Authors are encouraged to check ICMJE's guideline for authorship. (http://www.icmje.org/icmje-recommendations.pdf). Authorship problems will be dealt with according to COPE flowcharts. (https://publicationethics.org/authorship)
7. Open Access
There is an option of publishing your paper as Open Access. When you receive a formal acceptance email, you will find a link that you may click on to pay the Article Processing Charge (APC) for Open Access publishing.
